Leak Detection Spray(CLC 30)
NABAKEM CLC-30(COLOR LEAK CHECK)
Negotiable Min Order Quantity Unit
- Required Quantity
-
- Place of Origin
- South Korea
- Payment Terms
- L/C,Others
- Production method
- Available,ODM,OEM
- Shipping / Lead Time
- Negotiable / Negotiable
- Keyword
- leak check
- Category
- Other Chemicals
NABAKEM.CO.,Ltd
South Korea
- Verified Certificate
-
9
| Product name | Leak Detection Spray(CLC 30) | Certification | - |
|---|---|---|---|
| Category | Other Chemicals | Material | - |
| Keyword | leak check | Unit Size | - |
| Brand name | - | Unit Weigh | - |
| origin | South Korea | Stock | 10000 |
| Supply type | Available,ODM,OEM | HS code | 3207 |
Product Information
Features• Very fine defect may be detected.
• Defects found easily with naked eyes.
• Color is changed.(Yellow→Blue)
• No harmful for paint or metal.
Uses• Leakage of various pressure resistant piping may be detected.
• Gas tank, LPG tank, LNG tank etc.
• Gas tank, LPG tank, LNG tank etc.
How to Use1. Pretreatment of tested surface.
• Remove oil content, moisture and alkaline materials, if necessary.
• Especially if alkaline materials are adhered, flush tested surface with copious quantities of water and clean it with air or dustcloth.
Then dry it.
2. Ammonia gas fill up.
2. Ammonia gas fill up.
• Input ammonia gas into airtight tank or piping to make ammonia gas.
concentration 0.01~1% in terms of weight ratio.
Explosion range of ammonia gas combined with air is 15~28%, showing its concentration is safe.
concentration 0.01~1% in terms of weight ratio.
Explosion range of ammonia gas combined with air is 15~28%, showing its concentration is safe.
• High pressure inside tank makes detection sensitivity good.
But influence of pressure is not that remarkable. Therefore, inspection should be done at the pressure (several mmHg~several tens of mmHg) slightly higher than atmospheric pressure.
But influence of pressure is not that remarkable. Therefore, inspection should be done at the pressure (several mmHg~several tens of mmHg) slightly higher than atmospheric pressure.
3. Time of gas fill up and hold back should be over five minutes.
4. Application of detection agent.
• As powders of CLC-30 are dispersed in volatile solvent, shake its container till stirring bead is shaked well with clatter.
Then spray it evenly in the air before use.
Then spray it evenly in the air before use.
thinly Spray it evenly and thinly to the surface of detected object. Thin film shortens detection time.
5. Inspection.
5. Inspection.
• Leakage points are changed from yellow to blue normally within 5∼10 minutes.
• Large leakage points shows large indication shape.
• Re-Inspection for about 30~60 minutes is required for sufficient detection of fine leakage points.
6. Post-treatment.
• Detection agent film after inspection is easily removed by dustcloth or wire brush.
• Mechanical removal by dustcloth or brush.
• Flushing by pressure water.
Cautions• Permance of indication.
Indication maintains permance over 24 hours by ammonia gas fillup alone.
When fillup gas is removed or temperature is over 70℃, decoloration occurs.
Use the product below 40℃.
• Influences of moisture.
When fillup gas is removed or temperature is over 70℃, decoloration occurs.
Use the product below 40℃.
• Influences of moisture.
When CLC-30 is combined with adhesive water or moisture, it becomes weak-acid to create corrosion. Remove moisture completely.
• Welding slag residual.
• Welding slag residual.
As covering materials of covered welding rod contains strong-alkaline components like water and glass, application of CLC-30 shows pseudo-decoloration as if there are cracks.
Neutralize the product with cleaner before inspection or remove the residues with wire brush.
Neutralize the product with cleaner before inspection or remove the residues with wire brush.
However, the residues do not cause any problems with CO2 weld not using flux, TIG weld, MIG weld and submerged arc weld using meting flux.
• Residual of oil in enlarged tube.
• Residual of oil in enlarged tube.
Weld between tube and tube plate of heat exchanger or boiler has alkaline materials of lubricants used for tube expansion, which tend to cause pseudo-discoloration.
The materials should be removed. Also oil remained in tube can not be removed easily.
It is highly recommended that cylinder oil or neutral lubricant of turbine oil should be used.
• Influences of surfactant.
It is highly recommended that cylinder oil or neutral lubricant of turbine oil should be used.
• Influences of surfactant.
When test is done by CLC-30 after air test, alkaline surfactant (detergent) is used for soap water for air test.
Even if it is neutral, it shows alkalinity by thermonolysis and tends to cause pseudo-discoloration.
Inpsection surface should be clean. Or right surfactant should be selected.
Or surfactant should be removed completely for inspection.
• Toxicity of solvent.
Or surfactant should be removed completely for inspection.
• Toxicity of solvent.
Low-toxic solvent is used.
Provide good ventilation when using it in copious qantity indoors.
• When using it at low temperature (above 5℃)
Provide good ventilation when using it in copious qantity indoors.
• When using it at low temperature (above 5℃)
Spraying it below 5℃, sprayed particles are thick and not applied evenly.
In this case, dip it in warm water at 20℃ ∼ 30℃ before use.(Be careful to prevent temperature from being above 40℃.)
• This flammable product uses high-pressure gas.
In this case, dip it in warm water at 20℃ ∼ 30℃ before use.(Be careful to prevent temperature from being above 40℃.)
• This flammable product uses high-pressure gas.
• Comply with following cautions.
1. Do not spray it toward flame.
2. Do not use it near stove and heater.
3. Do not use it in the room using fire.
4. Do not keep in the place above 40℃
5. Provide ventilation after using it in closed room.
6. Do not throw it into fire.
7. Punch the can after use and remove residual gas to throw it away.
8. Do not keep it in the closed place.
*Packaging Unit
Aerosol 420㎖/can, 20cans/Box
B2B Trade
| Price (FOB) | Negotiable | transportation | Air Transportation,Ocean Shipping |
|---|---|---|---|
| MOQ | Negotiable | Leadtime | Negotiable |
| Payment Options | L/C,Others | Shipping time | Negotiable |
- President
- Kim Jonghyeok
- Address
- Paengseong-eup, Chupalsandan 1-gil,204, Pyeongtaek-si, Gyeonggi-do, Korea
- Product Category
- Other Machinery & Industry Equipment
- Year Established
- 1980
- Company introduction
-
NABAKEM never stops thinking of the betterment ofitself, produces the chemicalproducts and Aerosols that are needed for a wide range of industries which suchas shipbuilding,automobile, steel, fabric, etc. NABAKEM shows remarkable growth with the best chemicalmaking skills and innovative facilities.
Please visit our website for further information.
www.nabakem.com
- Main Product
_2.jpg "Ceramic Queen_Superhydrophobic Nano_Ceramic Coating for cars_1")
